Search found 1586 matches

by badcatt
Yesterday, 22:14
Forum: '69 '70 Parts for Sale
Topic: Cobra Jet distributor D0ZF-12127-C 1970 428CJ 4 speed
Replies: 1
Views: 43

Re: Cobra Jet distributor D0ZF-12127-C 1970 428CJ 4 speed

Date would be good for my CJ Cougar. But mine is a automatic with A/C. Good luck with the sale. It might be good for Mike Banks Eliminator.
by badcatt
16 Sep 2018, 12:00
Forum: Classic Cougar Community Discussion
Topic: Carb/Vacuum question
Replies: 16
Views: 338

Re: Carb/Vacuum question

bsbeck wrote:
16 Sep 2018, 11:40
Badcatt, my question is should it be pulling vacuum FROM the distributor? I unhooked it from the carb when it idling in park and there is no vacuum. I thought there would be.
Yes it should have vacuum at idle.
by badcatt
16 Sep 2018, 09:44
Forum: Classic Cougar Community Discussion
Topic: Carb/Vacuum question
Replies: 16
Views: 338

Re: Carb/Vacuum question

I think your vacuum line may be attached to the wrong port on the carburetor. I don't know edelbrock carbs very well, but I remember seeing several vacuum ports on them.
by badcatt
16 Sep 2018, 09:39
Forum: Classic Cougar Maintenance Restoration and Repair
Topic: Dash and headlights flash on and off
Replies: 3
Views: 93

Re: Dash and headlights flash on and off

There is a circuit breaker in the headlight switch. If you have halogen headlight bulbs they draw too much current and yield the results that you describe. If you don't have halogen headlights then the switch needs to be replaced due to a weak circuit breaker. The circuit breaker go get week over t...
by badcatt
14 Sep 2018, 17:56
Forum: Classic Cougar Maintenance Restoration and Repair
Topic: location of sequential flasher can
Replies: 11
Views: 200

Re: location of sequential flasher can


The first diagram does not have a few of the XR-7 and GT items on it. This one should fill in any blanks. I have a full set of factory wiring diagrams for 1970 and 1971. I have some from 1969.
by badcatt
14 Sep 2018, 09:00
Forum: Classic Cougar Maintenance Restoration and Repair
Topic: location of sequential flasher can
Replies: 11
Views: 200

Re: location of sequential flasher can


This is what the 71 Wiring diagram shows for location(I'm pointing with a green pin. I had the panel down in mine last winter checking to make sure there were no problems.
by badcatt
13 Sep 2018, 21:50
Forum: Classic Cougar Community Discussion
Topic: Premium on Eliminators - worth it?
Replies: 11
Views: 353

Re: Premium on Eliminators - worth it?

If someone wants to build a "tribute" or "Clone" car, more power to them. As long as the plan is not to deceive someone for monetary gain. I built 2 Eliminator Clones in my past. One back in the 80's when we never saw one around this part of the country and the other in the mid 90's to replace the r...
by badcatt
13 Sep 2018, 21:40
Forum: Classic Cougar Maintenance Restoration and Repair
Topic: location of sequential flasher can
Replies: 11
Views: 200

Re: location of sequential flasher can

There is a pannel above the glove box. If I remember correctly itis held in place with 2 Philips head screws. it has all the relays and flasher cans on it.
by badcatt
12 Sep 2018, 16:24
Forum: Classic Cougar Maintenance Restoration and Repair
Topic: 1970 with tilt and cruise?
Replies: 6
Views: 182

Re: 1970 with tilt and cruise?

The dealer would have had access to a Ford/Mercury install kit made by one of two suppliers (systems look different under the hood) They might have sent it out to Sears or another shop around town and tacked on some $$ for profit or installed the company system . Either would be noted on the factor...
by badcatt
09 Sep 2018, 19:58
Forum: Classic Cougar Community Discussion
Topic: Cougar by the numbers
Replies: 18
Views: 843

Re: Cougar by the numbers

karguy12 wrote:
09 Sep 2018, 16:08
How about how many 1968's with the 428cj and a 4:30 axle?
The book does not give numbers for rear axle ratios. But I bet it is only a few...